During the washing machine's spin cycle, the centrifugal force can be used to throw the water molecules on the clothes radially outwards because it acts along the radius.
How does a washing machine use centrifugal force?Your clothes are pushed toward the edges of the washing machine, which are frequently punctured with tiny holes, by this centrifugal force. After being pressed against the machine's sides, the force removes the water from your clothes.
What is the force that you apply to a machine?The input force or effort force is the force you apply to the machine. The term "output force" or "resistance force" refers to the force that the machine produces. By increasing either force or distance or changing the direction of force, a machine makes work simpler.
To know more about centrifugal force visit :-
https://brainly.com/question/17167298
#SPJ4
Beautiful family please can anyone help me with the question in the image below. Thanks
There are several possible explanations for the discrepancy in plagioclase presence between samples HOR1, HOR3, and HOR4:
Difference in initial mineralogy: The three samples may have had different initial mineralogy, which would result in different compositions and reactions during uplift.
Different rates of uplift: Samples HOR1 and HOR3 may have experienced uplift at different rates than sample HOR4, which could have affected the kinetics of the reaction and resulted in different mineral assemblages.
Differences in fluid composition: The fluid composition, including temperature, pressure, and chemical composition, can affect the reaction kinetics and the resulting mineral assemblages. Samples HOR1 and HOR3 may have experienced different fluid compositions during uplift than sample HOR4, which could explain the absence of plagioclase.
What are the other response?In response to question b)
Chloritization:
Diopside + H₂O + Mg₂+ => Mg-chlorite + SiO₂(aq) + Na+
Anorthite + H₂O + Mg₂+ => Mg-chlorite + SiO₂(aq) + Ca+
Albitization of plagioclase:
Anorthite + H₂O => Albite + SiO₂(aq) + Na+
Therefore, In the above reaction, the anorthite component of the plagioclase mineral is altered to albite, with the transfer of Na+ from the rock to the fluid. The total chemical composition of the rock is altered, with the albite component replacing the anorthite component.
Learn more about Mineral from
https://brainly.com/question/15844293
#SPJ1
See full question below
Task 3
a) In the class you have studied thin sections of peridotite samples HOR1, HOR3, and HOR4. Sample HOR4 locally shows coexisting spinel and plagioclase in fine-grained aggregates, which may indicate a spinel breakdown reaction during ophiolite uplift. Remarkably, no plagioclase is observed in samples HOR1 and HOR3, even though these rocks had a similar uplift history. Discuss possible explanations for this discrepancy!
b) In the class you have studied a number of rocks that had been subject to hydrothermal alteration. Write down the schematic reactions and qualitative element transfer between rock and seawater for the alteration reactions listed below. You do not have to balance the equations. Examples:
Mineralı + H2O + Element1 => Mineral2
Mineral + H2O => Mineral2 + Element1
Remember that the system is open for mobile cations (e.g., Na+, Ca2+, Mg2+) and SiO2(aq).
1) Chloritization: diopside + anorthite => Mg-chlorite
2) Albitization of plagioclase: anorthite component => albite
A discussion of the entry of a space vehicle into the earth's atmosphere after it has completed its mission in space appears in Ch.8. An approximate analysis of the vehicle motion and aerodynamic heating during atmospheric entry assumes an approximate atmospheric model called the exponential atmosphere, where the air density variation with altitude is assumed to be Po where p, is the sea-level density and h is the altitude measured above sea level This equation is only an approximation for the density variation with altitude throughout the whole atmosphere, but its simple form makes it useful for approximate analyses. Using this equation, calculate the density at an altitude of 45 km. Compare your result with the actual value of density from the standand altitude tables. In the preceding equation, assume that T-240 K (a reasonable representation for the value of the temperature between sea level and 45 km. which you can see by scanning down the standard atmosphere table)
A variable increases or declines at a pace proportional to its present value in a relationship described by an exponential function.
The formula for exponential functions is y = a(b)x, where a and b are constants and x is the independent variable. For the specified function; P = (0.99987) ᵃ And is the height in metres. By adding the height to the equation, the altitude at 5000 feet can be computed. But first, we must convert from feet to metres. 1m Equals 12 feet. 5000 feet Equals x metres. x=1524 metres. putting the values in the equation as substitutes; P = (0.99987) ¹⁵²⁴. The provided exponential function yields 0.82atm as the pressure at 500 feet. 0.82 atmospheres are P. In a connection modelled by an exponential function, a variable grows or shrinks according to its present value.
Learn more about Exponential functions here:
https://brainly.com/question/30559804
#SPJ4
2. 18 LAB: Warm up: Variables, input, and type conversion (1) Prompt the user to input an integer between 32 and 126, a float, a character, and a string, storing each into separate variables. Then, output those four values on a single line separated by a space. (Submit for 2 points)
That the separator between the data is specified using the'sep' option of the 'print()' method. We changed it to a space in this instance.
What is string?Traditionally, a string is just a list of characters, either as a literal constant or as a form of variable. The latter can have a set length or allow its components to be changed (after creation). Strings are used to store text and characters. A string of characters is, for instance, "Hello World." C lacks a String type that would allow for the quick creation of string variables, in contrast to many other programming languages. Programming data types called strings represent words rather than integers. A string is a group of characters that can include any combination of letters, numbers, symbols, and spaces.
What is string in Java?Collections of characters known as strings are widely employed in Java programming. Objects in the Java programming language include strings. The String class is provided by the Java platform for producing and modifying strings.
The following Python code will ask the user to enter an integer, a float, a character, and a string, store each of them in a different variable, then output them on a single line after being separated by a space:
# Request an integers between 32 & 126 from the user.
num = int(input("Enter an integer between 32 and 126: "))
# prompt the user to input a float
flt = float(input("Enter a float: "))
# request a character from the user
char = input("Enter a character: ")
# prompt the user to input a string
string = input("Enter a string: ")
# output the values on a single line separated by a space
print(num, flt, char, string, sep=' ')
To know more about String visit:
https://brainly.com/question/13262184
#SPJ1
A sample contains 10. 5 g of the radioisotope pb-212 and 157. 5 g of its daughter isotope, bi-212. How many half-lives have passed since the sample originally formed?.
Four half-lives after the sample's creation, the sample must have passed. This kind of radioactive decay is common, and all radioactive processes adhere to first order kinetics.
What is an isotope's longest half-life?The half-life of xenon-124, or the typical amount of time needed for a collection of xenon-124 atoms to decay by half, is about 18 sextillion years (1.8 x 1022 years), or roughly 1 trillion times the universe's present age.
How long is a radioactive isotope's half-life?Half-life is a unit used to describe the rate of radioactive isotope decay. A radioactive material's half-life is the amount of time it takes for half of its atoms to break apart.
To know more about half-lives visit :-
https://brainly.com/question/1439925
#SPJ4
What must a pilot do before entering Class G airspace?
Class B; The ATC facility in charge of a Class B airspace area must grant ATC clearance to every pilot flying in that area.
All aircraft operating in Class B airspace, unless otherwise authorized by ATC, shall be equipped with an operational transponder and automatic altitude reporting system as described in 14 CFR part 91, section 91.215(a), as well as an operational two-way radio capable of communicating with ATC on the applicable frequencies. After receiving training and an instructor's endorsement, student, sport, and recreational pilots are permitted to fly in particular Class B airspaces. In some Class B airports, even with the endorsement, students are not allowed. It is necessary to have a VOR or TACAN receiver, an encoding altimeter, and a 4096-code transponder. Class B; Every pilot operating in a Class B airspace area requires ATC approval from the ATC facility in charge of that area.
Learn more about Class B airspace here:
https://brainly.com/question/29752302
#SPJ4
if we have the same initial condition, but the idea air flow is pressurized by a compressor and we measured the exit temperature is 500k, and the system flow rate 1kg/s. if we ignore the kinetic energy and potential energy change, and the system is adiabatic. determine the work need, in kw.
Knowing the initial temperature and specific heat is necessary to calculate the value of Work = (kW) = (m * c * (500 - T_initial)) / 1000
The First Law of Thermodynamics, which states that the heat introduced to a system plus the work performed by the system equals the change in internal energy of a system, can be used to calculate the work performed by a system. in a system that is adiabatic.
ΔU = m * c * ΔT
where T is the change in temperature, c is the specific heat capacity, and m is the mass flow rate (in kg/s) (in K). The system's work can be encapsulated as:
W = ΔU
We can write: Given that the temperature at the compressor's outlet rose from the starting temperature to 500 K:
Knowing the initial temperature and specific heat is necessary to calculate the value of W.
W = m * c * (500 - T_initial)
W (kW) = (m * c * (500 - T_initial)) / 1000
Learn more about work Visit: brainly.com/question/25573309
#SPJ4
What is the Applications of AISI 8650 Alloy Steel?
Answer:
It is commonly used in a variety of applications that require strength and toughness, such as gears, crankshafts, and connecting rods in the automotive and aerospace industries. AISI 8650 steel is also commonly used for the manufacture of mechanical parts and tools, as well as for the production of cold-heading wire and nails.
In addition, AISI 8650 steel has good fatigue resistance and is often used for the manufacture of parts that are subjected to repeated loading and stress, such as springs and fasteners. Its good machinability makes it a popular choice for a variety of machine parts, including shafts, spindles, and gears. Its high hardness and strength also make it suitable for the production of high-strength fasteners, such as bolts and nuts.
Overall, the versatility and performance of AISI 8650 steel make it a popular choice for a variety of applications in the automotive, aerospace, and industrial sectors.
how containers & serverless computing is poised to/currently is changing the attack surface for hackers and network defenders. What effect is this having on potential forensic artifacts that would exist when an attack compromises a system? What is fueling the trend to move towards contains and serverless computing platforms like Docker?
With a serverless application, you can deploy a simple application or one that is easily divided into several smaller microservices. Alternatively, a bigger, trickier application.
What feature do containers and serverless have in common?Both are cloud-based, and serverless computing significantly reduces infrastructure overhead compared to containers. Applications are divided into smaller components and delivered in both types of architecture. Each container in a container-based architecture will execute a single microservice.
What does the forensic term "artefacts" mean?Forensic artefacts, The forensic items with some forensic value are called forensic artefacts. Any item that records information or provides proof of an event, such as logs, registers, hives, and many more.
To know more about application visit:-
https://brainly.com/question/28650148
#SPJ1
A hollow cast iron 5m long column with both ends fixed is required for support a load of 1000KN if the external diameter of the column is 250mm find its thickness take working stress as 80mpa and rankings constant as 1/1600
The required thickness of the cast iron column is approximately 16.8mm. we can use the formula for the buckling stress of a column:σ_critical = π^2 * E / (KL/r)^2
What is buckling Stress?
The abrupt change in shape (deformation) of a structural component under load, such as the bowing of a column under compression or the wrinkling of a plate under shear, is referred to as buckling in structural engineering.
To find the required thickness of the cast iron column, we can use the formula for the buckling stress of a column:
σ_critical = π^2 * E / (KL/r)^2
where σ_critical is the critical buckling stress, E is the modulus of elasticity of cast iron, K is the Rankine's constant (1/1600 for a fixed-fixed column), L = length of the column, and r = radius of the column.
The external diameter of the column is 250mm, so the radius is r = 250/2 = 125mm.
The modulus of elasticity for cast iron is around 200,000 N/mm^2.
We can then calculate the critical buckling stress:
σ_critical = π^2 * 200,000 / (1/1600 * 5000/125)^2
σ_critical = 80 N/mm^2
Since the working stress of the column is 80 N/mm^2, which is equal to the critical buckling stress, we can calculate the required thickness t using the formula for stress in a column:
σ = P / (π * r^2 / 4)
where P is the load on the column, and π * r^2 / 4 is the cross-sectional area of the column.
Given that the load on the column is 1000 KN, we can calculate the required thickness:
t = P * 4 / (π * r^2 * σ)
t = (1000 * 1000) * 4 / (π * 125^2 * 80)
t = 16.8 mm
To know more about buckling stress, visit: https://brainly.com/question/29799880
#SPJ1
Which energy source would produce the greatest amount of emissions?a. fossil fuels b. nuclear fuels c. solar energyd. wind energy
Option b is Correct. The energy source using nuclear fuels would generate the most emissions. Due to routine maintenance and/or refueling at these facilities, natural gas and coal capacity factors are often reduced.
Due to its lower maintenance requirements and ability to run for extended periods of time without refueling, nuclear power plants are often used more frequently (typically every 1.5 or 2 years).
Renewable plants are primarily constrained by a lack of fuel and are regarded as variable or intermittent sources (i.e. wind, sun, or water). These plants therefore require a backup power source, such as large-scale storage (not yet feasible at grid-scale), or they can be coupled with a dependable baseload power source, such as nuclear energy. An average nuclear reactor can generate 1 GW of power.
Learn more about nuclear fuels Visit: brainly.com/question/3983718
#SPJ4
Which of the following statement(s) is/are correct about the following problem? Finding equal number of a’s followed by equal number of b’s (anbn) is possible/impossible with C - - language.
Explanation:
Yes, it is possible to find a solution for this problem with C-- Language if there want and decrement operations and another variable to determine change of state from a to b.
Who invented a machine called a lasting machine that stitched the leather of a shoe to its sole?
Answer:
Jan Matzeliger
Explanation:
water flows upstream in a pipe through a vertical contraction (venturi) section. two piezometers are attached to the upstream pipe. the velocity at the inlet is 10. ft/s the difference in elevation between the two water levels in the piezometers is 6 inches. what is the water velocity (in ft/s) at the neck of the venturi?
In fluid mechanics, the Bernoulli equation can be used to determine the velocity of a fluid flowing through a pipe with a constriction or venturi section.
This equation relates the pressure, velocity, and height of a fluid at different points along the pipe. The Bernoulli equation states that the sum of the pressure, kinetic energy, and potential energy per unit volume of a fluid is constant at any point along a streamline. This can be expressed as:
P + 1/2 ρV² + ρgh = constant
where,
P is the pressure,
V is the velocity,
ρ is the density,
g is the acceleration due to gravity, and
h is the height above a reference level.
In this problem, we can use the Bernoulli equation to relate the pressures at the two piezometers to the velocity at the neck of the venturi section. Since the pipe is vertical, we can assume that the height difference between the two piezometers is due solely to the pressure difference.
At the inlet to the venturi section, the pressure is atmospheric and the velocity is 10 ft/s. At the neck of the venturi section, the cross-sectional area is smaller, so the velocity is higher.
Let Vₙ be the velocity at the neck of the venturi section.
Using the Bernoulli equation, we can write:
[tex]P_{1} + \frac{1}{2} \rho V_{1}^{2} = P_{2} + \frac{1}{2} \rho Vn^2[/tex]
where,
P₁ and P₂ are the pressures at the two piezometers, and ρ is the density of water.
Since the pressure difference is given by the height difference between the two piezometers, we can write:
P₁ - P₂ = ρgh
Substituting this into the Bernoulli equation, we get:
[tex]\frac{1}{2} \rho V_{n}^{2} - \frac{1}{2} \rho V_{1}^{2} = \rho gh[/tex]
Solving for Vₙ, we get:
[tex]V_{n} = \sqrt{(2gh + V_{1}^{2})[/tex]
Substituting the given values, we get:
[tex]V_{n} = \sqrt{(2 \times 32.2 \times 0.5 + 10^2)}[/tex]
= 11.6 ft/s
Therefore, the water velocity at the neck of the venturi section is 11.6 ft/s.
To know more about fluid mechanics: https://brainly.com/question/12977725
#SPJ4
A worker was attempting
to correct an electrical problem involving two non-
operational lamps. He proceeded to the area where he thought the problem
was. He had not shut off the power at the circuit breaker panel nor had he
tested the wires to see if they were live. He was electrocuted when he
grabbed the two live wires and then fell from the ladder. What could have
been done to prevent this accident from occurring?
To prevent this electrical accident from occurring, the following steps could have been taken:
Turn off the power at the circuit breaker panel: The worker should have turned off the power to the circuit before working on it to ensure that the wires were not live and avoid the risk of electrical shock.
Test the wires: Before attempting to correct the electrical problem, the worker should have used a non-contact voltage tester to verify that the wires were not live and safe to touch.
What is the electrical problem?Other points includes:
Use proper protective equipment: The worker should have been wearing protective equipment, such as rubber-soled shoes, gloves, and safety glasses, to reduce the risk of electrical shock.
Lastly, Follow established safety procedures: The worker should have followed established electrical safety procedures and received proper training on how to safely work on electrical circuits.
Learn more about electrical problem from
https://brainly.com/question/14407771
#SPJ1
a single-phase 240-volt load is drawing 43 amps and connected to the secondary of a 25 kva 480-volt primary to 240-volt secondary transformer. how much current is flowing in the primary winding?
There are two possible phases for a transformer's secondary voltage: in phase and out of phase. On how the windings are wound, this will happen.
What exactly do main and secondary mean in a transformer?In a static device known as a transformer, electricity is transferred from one circuit to another without changing the frequency. Primary winding refers to the winding that is connected to the supply, and secondary winding refers to the winding that has the load connected.
How do main and secondary windings differ from one another?The winding that receives electricity from the source is called the primary winding. The coil that supplies the load with energy at the modified or altered voltage is known as the secondary winding.
To know more about windings visit :-
https://brainly.com/question/12005342
#SPJ4
Compared to higher-level languages, which of the following are benefits of Assembly Language programming? (Check all that apply)
a. Ease of Use
b. Direct Manipulation of Memory
c. Intuitive Programs
d. Hands-on Code Optimization
e. Integrated Tools
A relational database's data can be accessed and altered using the special-purpose computer language known as structured query language (SQL).
For managing data stored in relational database management systems or for stream processing in relational data stream management systems, the domain-specific programming language known as SQL is utilized. Relational databases are managed by using a standardized programming language called Structured Query Language (SQL), which is also used to perform various operations on the data they hold. Data maintained in relational databases can be extracted, arranged, managed, and changed using a standard computer language called Structured Query Language (SQL). SQL is hence known as a database language that can perform operations on databases made up of tables with rows and columns.
Learn more about SQL here:
https://brainly.com/question/29582933
#SPJ4
Which Azure SQL Database service tier provides the fastest recovery time for a database?
The Azure SQL Database service tier with the fastest recovery time for a database is the Premium tier.
Why Azure SQL is Managed?Azure SQL Managed Instance is a fully managed SQL Server instance hosted in Azure that provides the compatibility and agility of an instance with the full control and management options of a traditional SQL Server on-premises deployment.
Azure SQL Managed Instance supports SQL Server Agent, which is important for scheduling and automating administrative tasks and maintenance operations.
The Premium tier offers guaranteed recoverability with a Recovery Time Objective (RTO) of less than 5 minutes, and a Recovery Point Objective (RPO) of up to 15 minutes. The Premium tier also offers automated backups, point-in-time restores, and geo-replication.
The Azure SQL Database service tier with the fastest recovery time for a database is the Premium tier.
Read more about SQL server here:
brainly.com/question/5385952
#SPJ2
another term for the weakening of a signal over distance is: question 5 options: turnaround time dispersion insulation attenuation mitigation
Attenuation is another term for the signal's distance-dependent weakening. The weakening of a signal's strength due to noise, distance, or other external factors is known as attenuation.
What does signal attenuation mean?The loss of signal strength in networking cables or connections is known as attenuation. This can occur as a result of a variety of factors and is typically measured in voltage or decibels (dB). It might make signals hard to tell apart or distorted.
How does attenuation occur?Any kind of signal, analog or digital, can be attenuated. Attenuation, also known as loss, is a natural outcome of signal transmission over extended distances. Attenuation in conventional and fiber optic cables is measured in decibels (dB) per foot, 1,000 feet, kilometer, or mile.
To know more about attenuation visit :-
https://brainly.com/question/25124539
#SPJ4
When is the IR plan used?
The IR plan (Incident Response Plan) is used in the event of an incident or emergency to respond to and manage the situation. It outlines the procedures and responsibilities for responding to incidents such as natural disasters, cyber attacks, fires, or other emergencies. The IR plan is used to ensure a coordinated and effective response to minimize the impact of an incident and ensure the safety of individuals and the protection of assets. The IR plan is essential for organizations, especially in industries such as engineering and critical infrastructure, to prepare for and respond to unexpected events.
After improving their machine guarding program, a company's medical costs were reduced by over $60,000 in one
year. What type of benefit was this medical cost reduction?
A. Indirect benefit
B. Direct benefi
C. Both indirect and direct benefit
D. Neither indirect or direct benefit
Answer:
I believe the answer is D. Neither indirect or direct benefit
Explanation:
if I'm wrong then its B. Direct benefit
3. The _______on an electric motor provides information that will assist a
person in selecting, installing, and energizing the correct motor for the job.
Note that the nameplate or rating plate on an electric motor provides information that will assist a person in selecting, installing, and energizing the correct motor for the job.
Who invented the Electric Motor?The electric motor was not invented by a single individual, but rather its development involved the work of many scientists and inventors over time.
The earliest form of an electric motor was created in 1821 by Michael Faraday, who demonstrated the conversion of electrical energy into mechanical motion. Subsequent inventors such as Thomas Davenport, Nikola Tesla, and Galileo Ferraris made significant contributions to the development of the electric motor, paving the way for its modern-day applications in a wide range of industries.
Learn more about nameplate:
https://brainly.com/question/1414905
#SPJ1
Identify a Hypertext Markup Language (HTML) embedded element that contains programming scripts used to construct bitmap images and graphics.a. Canvas
b. Iframe
c. Object
d. Embed
JavaScript drawings can now be created programmatically using HTML5 canvas, which is used in conjunction with the canvas> tag.
The term "head element" refers to a container used to store hidden metadata. The element must be positioned between the html tag and the body tag. A document's metadata, or machine-readable information, include the document's title, author, page description, style sheets, keywords, scripts, and other information. As a result, the information stored in the head element is mostly data that can be processed by a machine rather than data that can be read by a human. This metadata has the benefit of not being seen on the page. The machine will be able to recognize and read it, though. HTML requires a head element, which should only be used once.
Learn more about Head element here:
https://brainly.com/question/4276446
#SPJ4
What PSI is polyethylene pipe?
Answer:
my boy it's 4 of them 100,125,160,200
Explanation:
5 stars pl.z and a thanks
_____ are used in standardized tests, including the SAT and GMAT tests, and to record votes in elections.
a. Optical character recognition (OCR) systems
b. Speech recognition devices
c. Optical mark recognition (OMR) systems
d. Magnetic Ink Character Recognition (MICR) devices
Answer:
О c. OMR Optical Mark recognition.
Explanation:
OMR are used in standarized tests, including the SAT and GMAT tests, and to record votes in elections.
...
Which of the following best defines a change analysis survey?
A. Determines if the safety council member changes are appropriate
B. Determines if the current hazard inventory and processes must be updated
C. Determines if the safety responsibilities for shift changes are in place
D. Determines if a worksite layout change is needed to match site specifications
2005-2023 AdvanceOnline Solutions, Inc. All rights reserved.
Submit
Answer:
D. Determines if a worksite layout change is needed to match site specifications.
A Foundation for a wall was dug and must half filled with concrete. The dimensions excavation of the Foundation is 450 m (300mm)(200mm) calculate the volume of concrete to be poured?
Answer:
Explanation:
1. Determine how thick you want the concrete
2. Measure the length and width that you’d like to cover
3. Multiply the length by the width to determine square footage
4. Convert the thickness from inches to feet
5. Multiply the thickness in feet by the square footage to determine cubic feet
= 22.35 m^3
= 789.4 ft^3
= 29.24 yd^3
Note that the volume of concrete to be poured is 0.0135 m³
To calculate the volume of concrete needed to half-fill the foundation, we need to first convert the dimensions from millimeters to meters, and then multiply by the desired fill percentage of 50%.
Length: 450 m = 0.45 m
Width: 300 mm = 0.3 m
Height: 200 mm = 0.2 m
The volume of the foundation is:
Volume = l x w x h
V = 0.45 m x 0.3 m x 0.2 m
V = 0.027 m³
To half-fill the foundation with concrete, we need to calculate 50% of the volume:
Volume of concrete = 0.5 x V
Volume of concrete = 0.5 x 0.027 m³
Volume of concrete = 0.0135 m³
Therefore, we need 0.0135 cubic meters of concrete to half-fill the foundation.
Learn more about Volume:
https://brainly.com/question/1578538
#SPJ1
when following another vehicle use low beam whenever you are within (True or False)
True, It is illegal to have your high beams on when passing by another car and the reason for that is because they're bright duh lol, and it may be a risk to blind the drivers eyeballs off.
Hope I helped sire
Answer: it true Dear <3
Explanation: I hope this helps^^
In the case below, the original source material is given along with a sample of student work. Determine whether the student is guilty of plagiarism.Original Source Material:There is a design methodology called rapid prototyping, which has been used successfully in software engineering. Given similarities between software design and instructional design, we argue that rapid prototyping is a viable method for instructional design, especially for computer-based instruction. References:Tripp, S. D., & Bichelmeyer, B. A. (1990). Rapid prototyping: An alternative instructional design strategy. Educational Technology Research and Development, 38(1), 31-44. Student Version:Rapid prototyping could be an advantageous methodology for developing innovative computer-based instruction (Tripp & Bichelmeyer, 1990). References:Tripp, S. D., & Bichelmeyer, B. A. (1990). Rapid prototyping: An alternative instructional design strategy. Educational Technology Research and Development, 38(1), 31-44. Which of the following is true for the Student Version above?
The act of presenting someone else's words or ideas as your own is known as plagiarism. By paraphrasing, you can put another person's ideas into your own words.
Is plagiarism possible when paraphrasing?Paraphrasing without crediting the original author is plagiarism because you are presenting someone else's ideas as if they were your own. However, paraphrasing is not plagiarism if the source is properly cited.
Is it illegal to copy someone else's work by paraphrasing?You might want to rephrase or paraphrase a book's paragraph or section for your paper if you like its content. Even though it is not against the law, paraphrasing must be cited inacademic papers as a professional courtesy.
To know more about paraphrasing visit :-
https://brainly.com/question/29890160
#SPJ4
A shaft carrying amid way rotor of weight 100 n and eccentricity 0. 1cm rotates at 1200 rpm assume the stifness of shaft 0. 2MN/m and external dambing ratio as 01
Perform Enumeration of MSSQL with Metasploit. You are an ethical hacker consultant working for CorpNet. CorpNet wants you to discover weaknesses in their public-facing servers. From outside of the CorpNet network, you have discovered one of their Windows servers named www3.corpnet.xyz with an IP address of 198.28.1.3. You believe a Microsoft SQL server is installed on this server, but it doesn't respond to the default TCP port of 1433.
In this lab, your task is to use the auxiliary/scanner/mssql/mssql_ping exploit in Metasploit to determine which TCP port Microsoft SQL is using.
A relational database's data can be accessed and altered using the special purpose computer language known as structured query language (SQL).
For managing data stored in relational database management systems or for stream processing in relational data stream management systems, the domain-specific programming language known as SQL is utilized. Relational databases are managed by using a standardized programming language called Structured Query Language (SQL), which is also used to perform various operations on the data they hold. Data maintained in relational databases can be extracted, arranged, managed, and changed using a standard computer language called Structured Query Language (SQL). SQL is hence known as a database language that can perform operations on databases made up of tables with rows and columns.
Learn more about SQL here:
https://brainly.com/question/29582933
#SPJ4
